Oxygen Cleaning Dive Gear - Part 2
By Francois Burman
In the previous article, we settled on the recommendation that equipment used to control any breathing gas mix containing 25 percent oxygen and above at typical scuba cylinder pressures should be designed and considered suitable for oxygen use.
Possible debates aside, we’ll examine what oxygen cleaning means. How often should gear be oxygen cleaned, and what does this process entail?
While you might expect a regular interval for oxygen cleaning, this is usually not the case. The criteria for cleaning high-pressure equipment and components are as follows:
Outside of these criteria, periodic cleaning between service intervals should not be necessary.
Oxygen cleaning of scuba equipment requires a well-planned, tested, and effective procedure consisting of seven essential steps.
Only properly trained, competent technicians should perform oxygen cleaning. Some industries require laboratory validation of cleanliness, but this is not usually the case in diving, as a well-designed process will effectively remove any readily flammable contaminants.
No amount of cleaning and inspection can guarantee completely safe equipment. However, as we saw in the first part of this series, fires occur infrequently and somewhat unpredictably. Proper oxygen cleaning can help ensure there is no combustible fuel and increase confidence in your safety.
Possible debates aside, we’ll examine what oxygen cleaning means. How often should gear be oxygen cleaned, and what does this process entail?
While you might expect a regular interval for oxygen cleaning, this is usually not the case. The criteria for cleaning high-pressure equipment and components are as follows:
- when put into service for the first time
- when replacing any components
- after servicing and before reassembly, including cylinders after hydrostatic testing and cylinder valves and first-stage regulators after servicing or repair
- when there is any form of suspected contamination
- when any reason to doubt cleanliness exists, such as uncontrolled disassembly of equipment, using an unauthorised component, or a lack of confidence in a component’s cleaning or a contracted cleaning service according to the equipment manufacturer’s requirements
Outside of these criteria, periodic cleaning between service intervals should not be necessary.
Oxygen cleaning of scuba equipment requires a well-planned, tested, and effective procedure consisting of seven essential steps.
- Initial inspection to determine whether it can be cleaned and how
- Initial mechanical cleaning to remove any visible dirt or contamination, followed by degreasing using a cleaning agent suitable for oxygen service
- Flush using clean, potable water to remove all cleaning agent residue.
- Dry using oxygen-compatible air or other gas, which must be oil-free.
- Final inspection for any remaining surface contamination, which can include any or all of the following: Use a bright white or UV light in a darkened inspection area, use a fine water spray on the components and look for instant beading, or wipe the cleaned area with a clean, lint-free, white cloth and inspect the fabric with a white or UV light (this works well for cavities and hard-to-view surfaces)
- Preserve the cleaning by immediately packaging or otherwise protecting the components from contamination.
- Document the process in writing and issue documentation for each item cleaned with a certificate, report, or sticker recording the technician, date, cleaning agents, and inspection methods.
Only properly trained, competent technicians should perform oxygen cleaning. Some industries require laboratory validation of cleanliness, but this is not usually the case in diving, as a well-designed process will effectively remove any readily flammable contaminants.
No amount of cleaning and inspection can guarantee completely safe equipment. However, as we saw in the first part of this series, fires occur infrequently and somewhat unpredictably. Proper oxygen cleaning can help ensure there is no combustible fuel and increase confidence in your safety.
Categories
2024
February
March
April
May
October
My name is Rosanne… DAN was there for me?My name is Pam… DAN was there for me?My name is Nadia… DAN was there for me?My name is Morgan… DAN was there for me?My name is Mark… DAN was there for me?My name is Julika… DAN was there for me?My name is James Lewis… DAN was there for me?My name is Jack… DAN was there for me?My name is Mrs. Du Toit… DAN was there for me?My name is Sean… DAN was there for me?My name is Clayton… DAN was there for me?My name is Claire… DAN was there for me?My name is Lauren… DAN was there for me?My name is Amos… DAN was there for me?My name is Kelly… DAN was there for me?Get to Know DAN Instructor: Mauro JijeGet to know DAN Instructor: JP BarnardGet to know DAN Instructor: Sinda da GraçaGet to know DAN instructor Trainer: Christo van JaarsveldGet to know DAN instructor: Gregory DriesselGet to Know DAN Instructor: Beto Vambiane
November
Get to know DAN Instructor: Dylan BowlesGet to know DAN instructor: Ryan CapazorioGet to know DAN Instructor: Tyrone LubbeGet to know DAN Instructor Trainer: Christo van JaarsveldGet to know DAN Instructor: Caitlyn MonahanSafety AngelsDiving With A PFODiving Anilao with Adam SokolskiScience Saves SharksUnderwater NavigationUnderstanding Dive Equipment Regulations
2023
January
March
Terrific Freedive ModeKaboom!....The Big Oxygen Safety IssueScuba Nudi ClothingThe Benefits of Being BaldDive into Freedive InstructionCape Marine Research and Diver DevelopmentThe Inhaca Ocean Alliance.“LIGHTS, Film, Action!”Demo DiversSpecial Forces DiverWhat Dive Computers Don\'t Know | PART 2Toughing It Out Is Dangerous
April
July
August
September
Mismatched Scuba Valves to Cylinder OutletsUnderwater Crime Scene InvestigatorsDive Boat Etiquette – From Yachts to rubber ducksTravel Smarter: Personal Safety While TravelingLiability in ContextLearning from Success. Learning from MistakeDive in the Fast Lane with DPVsKwaZulu Natal shipwrecks: The ProduceAvoid Diving With EarplugsThe Parting Shot